[bregma]

I disagree. There is nothing in the digitally sampled and modelled world comparable to plugging your guitar into a hot over-driven tube amp and showing the feedback who's the boss. Pure analog transistors don't give that luscious even harmonic distortion and usually just clip like a meth-addled dog stylist in a poodle-grooming station.

[n_kr]

As a guitarist with over 30 years of playing, and owner of many tube and non-tube amps, I disagree. Even experienced guitarist cannot reliably distinguish between transistor and tube circuits in a blind test. Having said that, if only the knowledge of playing a tube amp gives someone a better experience, even if its not empirically distinguishable, thats a perfectly valid reason to prefer it.

[utopcell]

Minor correction:

An experienced guitarist cannot distinguish between "captured" amps, or amps which at their core simulate vacuum tubes at the software level. I definitely can't tell the two apart. However, I believe it is easy to distinguish a pure vacuum tube-based circuit from a JFET/MOSFET-based one.

There do exist vacuum tube replacements like the AMT 12AX7WS [1] or Jet City's RetroVales [2], but I would argue that the fact that they try to emulate tubes via transistors is a strong indicator that the natural circuits for both sound distinct enough for guitarists.

[1] https://amtelectronics.com/new/amt-12ax7ws/

[2] https://web.archive.org/web/20190803060713/http://www.robert...

[cogman10]

Not who you are responding to, but I'd say the point I was making wasn't that the sound wasn't different (though, the differences are almost certainly not large enough that most people can tell the difference). But rather that if that exact sound profile is desirable, it's easy to reproduce with transistors alone.

The two products you list are proof of that.

[utopcell]

I see your point, though strictly speaking, the two products I mentioned mimic 12AX7 tubes, which are preamp tubes. I'm not aware of E2E designs that also mimic power tubes.

[otherme123]

Maybe recently, with impulse responses and Fractal Axes-like machines, you can get any sound from silicon. But in the 90's the difference between silicon guitarrists (Dimebag Darrell or Chuck Schuldiner) and tubes was clearly noticeable.

Also, some 90's lower end amps with a valve in the prev sounded way better than similar priced amps that opted for pure solid state, at least for metal music and high distortion. For the clean channel the difference between them was minor.

[kazinator]

But the transistor circuit designers have gone out of their way to put in "tube like" behaviors which result in extra circuits and components that don't appear in the tube amp, and which would not appear in a "high fidelity" transistor amplifier.

One very common trick that has appeared in transistor guitar amps from the 1970's and onward is current feedback. The return terminal of the speaker doesn't go straight to ground, but feeds a tiny current-sensing resistor, like 0.1 ohms. Signal from the current-sensing resistor is combined into the negative feedback. This gives the amp a nonzero output impedance against the speaker, which changes the frequency response: more power is driven at the frequencies where the speaker impedes more, like its resonant frequency (about 70 to 100 Hz for a 12" guitar speaker) and high frequencies (due to voice coil inductance: rises from about 2 kHz up or something like that).

This doesn't reproduce everything that happens with tubes, but it goes a long way.

I built a circuit like that into an off-the-shelf amplifier, with a switch. I tell you, whenever I switch that off, it's not long before it goes back on again. Without the current feedback, it's sounds blatty/tubby and lifeless. It's not just the frequency response, because even if we dial in a similar EQ curve before the amp to eliminate the difference, it's not "it".

The TubeWorks people have an interesting design in the MosValve 500 amp. Rather than using current feedback, that amp places the MOSFET output stage outside of the negative feedback loop. Negative feedback is drawn from the VAS (voltage amplification stage) before the output stage. That means that the speakers will see the impedance of the MOSFETs. Plus the supposedly "tube like" overdrive characteristics of the power devices will come into play when that thing is cranked. Because they are outside of the NFB loop, it will just be soft onset clipping. Here is the important thing: unusually, the VAS and the output stage are on separate power rails, and those of the VAS are a significantly higher voltage (+/- 93V versus +/- 71V). So it is hard to make the VAS clip; it requires a much higher signal than what it takes to make the output stage go into progressive clipping. When an output stage is included the feedback loop, like in almost every amplifier out there, the amp is perfectly linear up to the limit, and then clips really hard.

The schematic: https://img.photobucket.com/albums/v202/xr3drumx13/MV500Sche...

Tube amplifiers "do their thing" without extra gimmicks like this, though.