[mort96]

Okay now this is weird.

I can reproduce it just fine ... but only when compressing all PDFs simultaneously.

To utilize all cores, I ran:

    $ for x in *.pdf; do zstd <"$x" >"$x.zst" --ultra -22 & done; wait

(and similar for the other formats).

I ran this again and it produced the same 2M file from the source 1.1M file. However when I run without paralellization:

    $ for x in *.pdf; do zstd <"$x" >"$x.zst" --ultra -22; done

That one file becomes 1.1M, and the total size of *.zst is 37M (competitive with Brotli, which is impressive given how much faster it is to decompress).

What's going on here? Surely '-22' disables any adaptive compression stuff based on system resource availability and just uses compression level 22?

[terrelln]

Yeah, `--adaptive` will enable adaptive compression, but it isn't enabled by default, so shouldn't apply here. But even with `--adaptive`, after compressing each block of 128KB of data, zstd checks that the output size is < 128KB. If it isn't, it emits an uncompressed block that is 128KB + 3B.

So it is very central to zstd that it will never emit a block that is larger than 128KB+3B.

I will try to reproduce, but I suspect that there is something unrelated to zstd going on.

What version of zstd are you using?

[mort96]

'zstd --version' reports: "** Zstandard CLI (64-bit) v1.5.7, by Yann Collet **". This is zstd installed through Homebrew on macOS 26 on an M1 Pro laptop. Also of interest, I was able to reproduce this with a random binary I had in /bin: https://floss.social/@mort/115940378643840495

I was completely unable to reproduce it on my Linux desktop though: https://floss.social/@mort/115940627269799738

[terrelln]

I've figured out the issue. Use `wc -c` instead of `du`.

I can repro on my Mac with these steps with either `zstd` or `gzip`:

    $ rm -f ksh.zst
    $ zstd < /bin/ksh > ksh.zst
    $ du -h ksh.zst
    1.2M ksh.zst
    $ wc -c ksh.zst
     1240701 ksh.zst
    $ zstd < /bin/ksh > ksh.zst
    $ du -h ksh.zst
    2.0M ksh.zst
    $ wc -c ksh.zst
     1240701 ksh.zst
    
    $ rm -f ksh.gz
    $ gzip < /bin/ksh > ksh.gz
    $ du -h ksh.gz
    1.2M ksh.gz
    $ wc -c ksh.gz
     1246815 ksh.gz
    $ gzip < /bin/ksh > ksh.gz
    $ du -h ksh.gz
    2.1M ksh.gz
    $ wc -c ksh.gz
     1246815 ksh.gz

When a file is overwritten, the on-disk size is bigger. I don't know why. But you must have ran zstd's benchmark twice, and every other compressor's benchmark once.

I'm a zstd developer, so I have a vested interest in accurate benchmarks, and finding & fixing issues :)

[mort96]

Interesting!

It doesn't seem to be only about overwriting, I can be in a directory without any .zst files and run the command to compress 55 files in parallel and it's still 45M according to 'du -h'. But you're right, 'wc -c' shows 38809999 bytes regardless of whether 'du -h' shows 45M after a parallel compression or 38M after a sequential compression.

My mental model of 'du' was basically that it gives a size accurate to the nearest 4k block, which is usually accurate enough. Seems I have to reconsider. Too bad there's no standard alternative which has the interface of 'du' but with byte-accurate file sizes...

[terrelln]

Yeah, it isn't quite that simple. E.g. `/bin/ksh` reports 1.4MB, but it is actually 2.4MB. Initially, I thought it was because the file was sparse, but there are only 493KB of zeros. So something else is going on. Perhaps some filesystem-level blocks are deduped from other files? Or APFS has transparent compression? I'm not sure.

It does still seem odd that APFS is reporting a significantly larger disk-size for these files. I'm not sure why that would ever be the case, unless there is something like deferred cleanup work.

[mort96]

Ross Burton on Mastodon suggests that it might be deduplication; when writing sequentially, later files can re-use blocks from earlier files, while that isn't the case as much when writing sequentially. That seems plausible enough to me.

[Zekio]

doesn't zstd cap out at compression level 19?

[mort96]

From the man page:

    --ultra: unlocks high compression levels 20+ (maximum 22), using a lot more memory.

Regardless, this reproduces with random other files and with '-9' as the compression level. I made a mastodon post about it here: https://floss.social/@mort/115940378643840495