[vlachen]

I've turned a few wrenches as a life-long DIY mechanic, a former aircraft mechanic, and a mechanical engineer. I use the Hazard Fraught method of tool purchases: I will buy a tool from Harbor Freight once. If it fulfills my needs great. Job done and it goes into the toolbox. If I use it so hard it gives up the ghost, then it gets chucked into the fuckit-bucket and I go buy it at higher quality.

To be honest, Harbor Freight and other store brands (Husky, Kobalt, etc) have always been reliable enough. As a home-gamer, I certainly couldn't see being able to have a toolbox full of Snap-On, especially before completing my engineering degree.

If I were a pro and feeding my family depended on what those tools did, then I could certainly see Snap-On as an investment, as my father did when he ran his own shop. But, to the point about rounding off a nut, something like that is rarely a function of tool quality and more about technique. Yes, a cheap 12 point socket or wrench can round off a hex pretty badly, but if it happens, the whole setup has probably been giving warning signs the entire time. My experience is that cheap tools are more likely to snap, break, or shatter during heavy loading, but that's not often the default use case.

[subhro]

> I've turned a few wrenches as a life-long DIY mechanic, a former aircraft mechanic, and a mechanical engineer. I use the Hazard Fraught method of tool purchases: I will buy a tool from Harbor Freight once. If it fulfills my needs great. Job done and it goes into the toolbox. If I use it so hard it gives up the ghost, then it gets chucked into the fuckit-bucket and I go buy it at higher quality.

Now you either have a tool that might be unreliable and can cause you trouble for the next job. Or, you spent money that you didn't have to spend by buying the lower grade tool when you needed to buy something better anyway.

> To be honest, Harbor Freight and other store brands (Husky, Kobalt, etc) have always been reliable enough. As a home-gamer, I certainly couldn't see being able to have a toolbox full of Snap-On, especially before completing my engineering degree.

Here you have a solid point. I am thankful that I am able to afford good tools. But if someone in unable to justify, I would say either work to be able to justify it, rent, or buy the best you can afford if you need the tool right now.

> But, to the point about rounding off a nut, something like that is rarely a function of tool quality and more about technique.

Maybe you are right. But here is an exaggerated example. You have a socket that has more clearance than ideal. You loosen one nut, and that was okay, you loosen the second one, that was a little tighter and that whole setup flexed a bit, but turned out okay. The third one is where things slip. Now, you have a problem. At least that is more or less how I land into trouble.

[hansvm]

> Now you either have a tool that might be unreliable and can cause you trouble for the next job. Or, you spent money that you didn't have to spend by buying the lower grade tool when you needed to buy something better anyway.

The "unknowns" point is valid, but the advice to buy something cheap to start with still comes from a good place.

Even from a cost perspective, I've snapped a few wrenches and upgraded my box saw (,and will splurge on a solder iron the next time I do anything serious), but the money wasted in those mis-purchases is vastly less than the money I would have spent on getting the "right" tools at the outset.

You also have the problem of unknown unknowns. Plenty of people are willing to sell you a $25 tool for $250, and we all know how reviews work, so the presence of good reviews and a high price tag isn't sufficient to guarantee quality. Even going with a "good" brand doesn't suffice if the brand is willing to increase profits on a few duds here and there (or, more charitably, just doesn't always hit them out of the park) or goes the way of Lenovo after an acquisition. Buying a good tool is often a nontrivial effort, and (when directing that advice to your average homeowner rather than a professional with that particular tool) the experience you have with the bad tool gives you a starting point for figuring out which aspects you do or don't care about.

For a few small examples, I own the cheapest immersion blender, 16oz claw hammer, precision screwdriver set, ... that I could get my grubby little hands on. I'd make those purchases again in a heartbeat.

For a counter-example, I did the same thing with a diamond stone. It turns out I don't care about the surface area or most characteristics (and now I know), but I care quite a lot about the depth and longevity. I'll save more money getting a longer-lasting stone that's a size I need, despite having "wasted" money on the cheaper stone, since I won't be inadvertently getting something bigger than I need or want. Since those things last ages I'm not sure the point really holds, but it also lasted for years and was purchased at a time when money was tighter, and spending more money then would have been much more expensive than spending it now.

For an actual counter-example, now I know that any wrench where I'm applying more than a few hundred foot-pounds of torque absolutely needs to be forged, and I'm willing to splurge to avoid low-quality steel. The cheaper wrenches were properly wasted money. Compared to all the time and money I've saved only purchasing nice tools when something failed though, I still think it was a good strategy.

[vlachen]

>> I've turned a few wrenches as a life-long DIY mechanic, a former aircraft mechanic, and a mechanical engineer. I use the Hazard Fraught method of tool purchases: I will buy a tool from Harbor Freight once. If it fulfills my needs great. Job done and it goes into the toolbox. If I use it so hard it gives up the ghost, then it gets chucked into the fuckit-bucket and I go buy it at higher quality.

>Now you either have a tool that might be unreliable and can cause you trouble for the next job. Or, you spent money that you didn't have to spend by buying the lower grade tool when you needed to buy something better anyway.

An important note is that this is a conscious decision. I know that I cheaped out on something, and I'm often pleasantly surprised that it didn't break. But I'm not depending on it for food, and we have backup transportation methods, so I'm not completely hosed if it gives up. For example: I once spent $20 on a Harbor Freight corded angle grinder, with the understanding that it'll probably work for the one job I really needed it for at that moment. 15 years and half a dozen smoke checks later, the damned thing still runs hard.

>> To be honest, Harbor Freight and other store brands (Husky, Kobalt, etc) have always been reliable enough. As a home-gamer, I certainly couldn't see being able to have a toolbox full of Snap-On, especially before completing my engineering degree.

> Here you have a solid point. I am thankful that I am able to afford good tools. But if someone in unable to justify, I would say either work to be able to justify it, rent, or buy the best you can afford if you need the tool right now.

If you can, that's great. Most of my wrenching life, including working on multi-million dollar automation equipment, has been well serviced by budget tools. Anything pro-grade was handed down from my father after he closed his shop. I'm to the point now where I could reasonably afford to upgrade, but the handtools still work well, and my money/time is honestly spent better right now paying a reputable shop to do what I need. Starting out in the world, I never thought I'd be able to say that, but I'm happy to be here now.

I'll have a project car again some day, and then I'll look hard at what is needed to accomplish my goals.

[sophacles]

I think a lot of your thinking here is assuming somewhat frequent use - and I agree when you are going to be using the tools often, just get a decent or good one. For a lot of tools though - well lets just say my tool chest has an awful lot of things I need that one time 20 years ago, and haven't needed since. Often I don't know which tools are going to be in that one-use category, so the algorithm "buy the cheap one, upgrade when needed" has overall saved me more than enough money to upgrade to the really good version even for tools I use relatively rarely.

[vlachen]

The other thing that I'll add here is that if the tool has a battery, then I'm going to a well established and supported brand. I know they love to change the technology (Lookin' at you DeWalt) but there are often workarounds. I'll buy into the tool ecosystem because the last thing I want to do is stop my flow to figure out which tool/battery is ready for the task at hand.

[genewitch]

Black and decker makes a corded drill motor that has the matrix attachments, between that and a hitachi hammer drill I'll never buy a cordless again.

[Scoundreller]

> But, to the point about rounding off a nut, something like that is rarely a function of tool quality and more about technique. Yes, a cheap 12 point socket or wrench can round off a hex pretty badly, but if it happens, the whole setup has probably been giving warning signs the entire time.

In the rust belt, about every bolt has lots of warning signs and each job is a gamble. I really need to get a torch.

[vlachen]

Knowing the tricks that come with your location are a big deal. I'm in a minor salt part of the US, so I don't often have to worry about pre-treating a fastener on our daily drivers. If it gets to the point that I'm breaking out the torch, I'm working on an outlier.

[genewitch]

"Can't be tight if it's a liquid!"