[sprachspiel]

This is for 8 SSDs and a single modern PCIe 5.0 has better specs than this.

[nik_0_0]

Is it? The line preceding the bullet list on that page seems to state otherwise:

“”

  Each storage volume can deliver the following performance (all measured using 4 KiB blocks):

  * Up to 8000 MB/second of sequential reads

“”

[sprachspiel]

Just tested a i4i.32xlarge:

  $ lsblk
  NAME         MAJ:MIN RM   SIZE RO TYPE MOUNTPOINTS
  loop0          7:0    0  24.9M  1 loop /snap/amazon-ssm-agent/7628
  loop1          7:1    0  55.7M  1 loop /snap/core18/2812
  loop2          7:2    0  63.5M  1 loop /snap/core20/2015
  loop3          7:3    0 111.9M  1 loop /snap/lxd/24322
  loop4          7:4    0  40.9M  1 loop /snap/snapd/20290
  nvme0n1      259:0    0     8G  0 disk 
  ├─nvme0n1p1  259:1    0   7.9G  0 part /
  ├─nvme0n1p14 259:2    0     4M  0 part 
  └─nvme0n1p15 259:3    0   106M  0 part /boot/efi
  nvme2n1      259:4    0   3.4T  0 disk 
  nvme4n1      259:5    0   3.4T  0 disk 
  nvme1n1      259:6    0   3.4T  0 disk 
  nvme5n1      259:7    0   3.4T  0 disk 
  nvme7n1      259:8    0   3.4T  0 disk 
  nvme6n1      259:9    0   3.4T  0 disk 
  nvme3n1      259:10   0   3.4T  0 disk 
  nvme8n1      259:11   0   3.4T  0 disk

Since nvme0n1 is the EBS boot volume, we have 8 SSDs. And here's the read bandwidth for one of them:

  $ sudo fio --name=bla --filename=/dev/nvme2n1 --rw=read --iodepth=128 --ioengine=libaio --direct=1 --blocksize=16m
  bla: (g=0): rw=read, bs=(R) 16.0MiB-16.0MiB, (W) 16.0MiB-16.0MiB, (T) 16.0MiB-16.0MiB, ioengine=libaio, iodepth=128
  fio-3.28
  Starting 1 process
  ^Cbs: 1 (f=1): [R(1)][0.5%][r=2704MiB/s][r=169 IOPS][eta 20m:17s]

So we should have a total bandwidth of 2.7*8=21 GB/s. Not that great for 2024.

[Aachen]

So if I'm reading it right, the quote from the original article that started this thread was ballpark correct?

> we are still stuck with 2 GB/s per SSD

Versus the ~2.7 GiB/s your benchmark shows (bit hard to know where to look on mobile with all that line-wrapped output, and when not familiar with the fio tool; not your fault but that's why I'm double checking my conclusion)

[Nextgrid]

If you still have this machine, I wonder if you can get this bandwidth in parallel across all SSDs? There could be some hypervisor-level or host-level bottleneck that means while any SSD in isolation will give you the observed bandwidth, you can't actually reach that if you try to access them all in parallel?

[highfrequency]

The aggregate throughput matches the advertised number of 22,400 MB/s: https://aws.amazon.com/blogs/aws/new-storage-optimized-amazo...

[dekhn]

Can you addjust --blocksize to correspond to the block size on the device? And with/without --direct=1

[zokier]

I wonder if there is some tuning that needs to be done here, it seems suprising that the advertised rate would be this much off otherwise.

[jeffbee]

I would start with the LBA format, which is likely to be suboptimal for compatibility.

[zokier]

somehow I4g drives don't like to get formatted

    # nvme format /dev/nvme1 -n1 -f
    NVMe status: INVALID_OPCODE: The associated command opcode field is not valid(0x2001)
    # nvme id-ctrl /dev/nvme1 | grep oacs
    oacs      : 0

but the LBA format indeed is sus:

    LBA Format  0 : Metadata Size: 0   bytes - Data Size: 512 bytes - Relative Performance: 0 Best (in use)

[jeffbee]

It's a shame. The recent "datacenter nvme" standards involving fb, goog, et al mandate 4K LBA support.

[dangoodmanUT]

that's 16m blocks, not 4k

[wtallis]

Last I checked, Linux splits up massive IO requests like that before sending them to the disk. But there's no benefit to splitting a sequential IO request all the way down to 4kB.

[jeffbee]

Those claims are per device. There isn't even an instance in that family with 8 devices.