[blown_gasket]

0C:F9:31:D2:DB:51

AB:33:C6:C6:19:74

I used a MAC address generator to get those two, but I think two is enough to make the discussion. Current reality aside, would you be able to identify those with binary math as being on the same network device, different network devices, across the world? MAC addresses on physical NICs are provided by the manufacturer, sure you can adjust them but I think that leaves the good-faith portion of this discussion.

So if you wanted to have those to communicate no matter what you would have to have a network device state: "I'm network device A, I have this device 0C:F9:31:D2:DB:51" then another state: "I'm network device B, I have this device AB:33:C6:C6:19:74". Then whenever 0C:F9:31:D2:DB:51 wants to talk with AB:33:C6:C6:19:74 it's network device will have to just send it to the next upstream network device or if there are multiple network devices that could be upstream you could send it to them all which is just not great for security whatsoever or you now have to do a recursive lookup for whatever n devices might yet be upstream and wait for a response to see if one of those has it. Overall trying to send ethernet frames globally without an IP network sounds like not a great idea.

[MiddleMan5]

So it seems like the primary use of IP, as you describe, is to define a way to narrow the search to sub address groups so as to not require enumerating every address in the scheme.

Still, there's doesn't seem to be any reason you couldn't just say "device 1 gets MAC 00:00:00:00:00:01" and "device 2 gets 00:00:00:00:00:02" and the gateway controller gets :::00 and there's a special address on :::FF that can be used to talk to everyone...

Is that it? Is that all there is to IP? A loose pattern for reducing search scope, a couple reserved addresses for special cases, and a balance between address bitsize and total number of unique addresses (without requiring additional routing complexity)?

It all seems so... simple

[vidarh]

You could. Assuming all your equipment supports setting the MAC, and you make sure to operate on prefixes so you can route by prefix. There's nothing stopping you from doing so.

The reason we don't is because at the time IP was introduced, there were many alternative physical layers in active use. And while Ethernet is near ubiquitous now, what we learnt from that was that it is unreasonable to assume that all your data will go over the same physical layer. And so you need a standard addressing format that will work elsewhere too.

Nothing stops you from stripping it back locally and using MAC addresses for everything internal to you, and ditching IP, and "just" gateway to/from IP. Lots of people did gateway between different protocols before IP became the dominant choice.

But you won't get everyone else to change because it'd require new firewall and new routers, and all kinds of software rewrites, and you can see how long the IPv6 transition has taken, so you'd still need to wrap and unwrap TCP/IP and find a way to address IP for everything that isn't 100% local, and even for lots of local-only stuff unless you want to rewrite everything.

There would be potential ways. E.g. you could certainly use a few bits to say "this is external" and then have some convention to pack an IPv4 address into the MAC or let an IPv6 address overflow into the data, and use that to make gatewaying and routing to external networks easier, while everything else just relies on the MAC. But you'd still need a protocol header for other things too, and then the question is how much benefit you would gain from ditching pretty much just ARP, which isn't exactly complex, a lookup table, and replacing the IPs in the header with just a destination MAC. Because the rest of the complexity is still there.

And you can gain most of the benefit of that by getting an IPv6 EUI64 address [1]. They'll work with "normal" IP equipment, and you can optimize in your own software by having the IP stack ditch ARP lookups when they see a local EUI64 address. Whether that optimisation actually makes a difference is another question.

[1] https://community.cisco.com/t5/networking-knowledge-base/und...

[coryrc]

It starts out simple :-).

Then you realize doing some action ends up being O(n^2) so you add some workaround in your switch and cache some things. And you know what they say about cache invalidation. And vendor A implemented it wrong in 1993 so you have a special case for their systems. And then you want to handle abuse cases. And authentication. And you're competing against the whole rest of the world and your thing isn't enough better.

[kortilla]

Then how do you send traffic to device1 on another network? You need globally unique addresses and hierarchy. Go back to the drawing board and come back when you’ve ended up inventing a worse IP protocol.

> It all seems so... simple

Because you haven’t even thought through basic use cases.