[wbraun]

The medium article links to a nature article which explains in depth: https://www.nature.com/articles/s41928-017-0010-z

This seems like an interesting development, but the performance gain appears to be limited to low value inductors in the 10's of GHz range. Those inductors are already very small and easily integrated on RF ICs.

If you want to miniaturize electronics you need to miniaturize the inductors used in power conversion, which typically operate in the KHz to low MHz range. It's a very different problem.

[AHappyCamper]

But it's a good start, no? And the theory has been proven as sound. I'm guessing/hoping they'll target the higher ranges soon.

[wbraun]

Its a material that basically gives electrons "inertia" which acts like an inductance derived from magnetic fields. There is a time constant to it, which determines at what frequency range it starts contributing to the inductance value.

To make it useful for power electronics they would have to push out this time constant by at least 4 orders of magnitude, I don't believe the theoretical material properties support that.

You might see this shaving off a few mm^2 from RF ICs and providing better RF performance. Applications in power electronics, where inductors take up the most volume, seems unlikely.

[superkuh]

On the flipside, kinetic inductance detectors (https://en.wikipedia.org/wiki/Kinetic_inductance_detector) for astronomy have been around since ~2000 and in the low light single photon regime they have much less noise on readout than photoelectric detectors (CCD/CMOS/etc).

[rini17]

Perhaps power electronics will move to higher frequencies, too.

[coryrc]

Will have to drive gate and source capacitance down a few orders a magnitude to make that a reasonable trade-off.

[bsder]

> Perhaps power electronics will move to higher frequencies, too.

They just did thanks to GaN transistors. The limitations in power electronics generally aren't the inductors.

[daddylonglegs]

The abstract [1] states that the technique is "purely material-enabled" but that they still laid out their kinetic inductor in a spiral. It would seem to me that a big advantage for these inductors in RF chips would be the lack of coupling to and from external magnetic fields if you used another layout.

One of the major limitations of existing planar spiral inductors is that their external magnetic fields will couple them to other nearby inductors creating a transformer. The big space saving for these could be the ability to lay down snake shaped inductors next to each other with very low coupling. Do they mention this in the article?

[1] I was unable to read the full article.

[amelius]

You can shield the magnetic coupling with materials with high permeability.

[regularfry]

You can, and that's more bulk, mass, and design complication.

[ezconnect]

Full text of the article. https://sci-hub.tw/10.1038/s41928-017-0010-z

[tgflynn]

> If you want to miniaturize electronics you need to miniaturize the inductors used in power conversion

Hasn't that problem mostly been solved already with switch mode power supplies that are pretty small.

With most personal electronics being battery powered these days I'm curious where you see a real need for further reduction in the size of power converters. In other words what technologies or devices are currently limited by the size of their power converters ?

[as-j]

> Hasn't that problem mostly been solved already with switch mode power supplies that are pretty small.

I waste a ton of board space with power supplies. Not everything is personal electronics with custom ICs* in the volume of an iPhone. So this means on my current design there's power supplies for 1v, 1v8, 2v5, 3v3, ~4v, 5v. Each of these the biggest component is the inductor.

I've sometimes joked, I make power supplies with a computer attached.

Edit: since the volume is low we use off the shelf parts which means we tend to end up with a variety of voltage requirements. And yes...reduction of rails is something that's part of components selection, alas....

[tgflynn]

Are all of those drawing significant current though ? If you just have some small component with an odd voltage requirement that doesn't need much current couldn't you supply it with something a lot simpler than a dc-dc converter, like maybe a voltage divider or linear regulator ?

[mlyle]

Almost certainly not a voltage divider. Maybe a linear, if efficiency doesn't matter.

[jmwilson]

> Hasn't that problem mostly been solved already with switch mode power supplies that are pretty small.

Perhaps you are thinking of "wall wart" power supplies that used line-frequency transformers in their rectifier design. These have been replaced and miniaturized by using offline switched-mode power supplies and point-of-load converters, but the magnetic components remain the largest components in these designs.

> With most personal electronics being battery powered these days I'm curious where you see a real need for further reduction in the size of power converters.

It's now common for modern SoC devices to require multiple voltage rails. It may require 3.3 V, 1.35 V, 1.8 V on separate pins and each requires a point-of-load converter for efficiency, and each of these take up board space.

[mrfusion]

So wall warts are obsolete? What breakthroughs replaced them?

[coryrc]

The cost of switching power supplies. (your USB charger the size of a plug puts out more power than a transformer wall wart 6x8x8 cm)

[Someone]

“Hasn't that problem mostly been solved already with switch mode power supplies that are pretty small“

It would still be useful to make them even smaller. For example, it’s often not possible to use all sockets in a power strip because of the size of power converters. Also, such smaller converters typically are a bit of a hassle to toss into a bag because of their somewhat awkward shape (especially if all other things in the bag are pencil-shoes or flat slates (laptop, tablet, notebook)

A transformer that fits inside an AC power plug would solve both problems.

I think that, _if_ we could build that, most people would start calling the current tiny converters bulky.

[foldr]

It would be useful to have lower profile inductors. It's difficult to get inductors less than 1mm high for use with low voltage boost/buck converters. ICs and other passive components can usually sit significantly less high above the board.

[mNovak]

Yes I think the focus is on RFICs where these take up a lot of die area. Potentially that's really important for more exotic processes like InP, GaN, or even diamond, where wafer space comes at a huge premium.

[a1369209993]

I assume the obvious solution of just running power conversion at GHz frequencies would waste too much power as EM radiation, correct?

[hetman]

At those frequencies you're going to be losing a lot of power in the switching losses of the transistors. Power MOSFETS have very low leakage when fully on or off, the largest loss tends to be during the transition when voltage and current are non zero. Because the speed of that transition is limited, the higher the frequency the more percentage of total time is spent in those transition phases and the higher the losses.

[a1369209993]

Yeah, that makes more sense than radio emissions, thanks.

[compumike]

Low efficiency due to thermal losses in transistors switching.