Don't forget the 128 bit vector ISA with 32 registers, supporting up to 64 bit int and FP, and with LMUL=8 you can process 1024 bits with a single instruction (at 3 cycles per 128 bits for most operations). Fully supported by GCC and CLANG (xTHeadVector) and compatible with RVV 1.0 with just a command line switch if you use the C intrinsic functions. (a lot of code working on 8 bit elements is binary compatible with RVV 1.0 too e.g. typical memcpy(), memset(), memcmp(), strlen(), strcpy(), strcmp())
When I bought my 64 MB Duo they were $3!
Then for a long time they were $5 for the 64 MB, $7 for the 256 MB, and $10 for the 512 MB.
Sadly, like everything else, they've gone up considerably this year.
The wild thing is that this SoC is a heterogenous compute device. It has three different kinds of cores: a pretty beefy arm64 core and two different RISC-V cores: a 1Ghz one for running Linux and a 700Mhz one dedicated to running a real-time operating system. The arm64 core can also run its own OS.
Also a user-programmable 300 MHz 8051 (8 bit) primarily there to manage timers and interrupts and wake up the big 64 bit cores.
Note that the application-processor 1 GHz C906 and Arm A53 are either/or, you can't run both at the same time — similar to the Arm M33 and RISC-V Hazard3 core pairs on the Raspberry Pi RP2350.
You can buy sub-$0.50 microcontrollers. But even at $5, I don't know why you'd want to run models on them, it's an environment constrained to the point of being useless for this task.
And I hope it stays that way, I don't want MCU shortages...
Many artificial environments are useless to tasks they were not designed for until somebody experiments, tests, redesigns, and iterates.
I'll give a specific example apropos of TFA. Computer vision models were never run on MCUs because they were constrained to the point of being useless for this task, but then someone tried the impractical, and now it's trivial[1]
Regarding MCU shortages, you should be worried about the supply chain, but I don't see the impact really being from running LLMs on ESP-32s, of all things.
Fun and learning is a really good reason. It also reminds me of the damascene: trying to achieve something that doesn't feel possible, and working through all the extreme resource-constrained engineering limits.
I think most of my embedded projects aren't that useful, but they've taught me a lot.
I'm not disagreeing with you, I think this goes beyond impractical, it's doomed from the get go.
In my book, impractical means "I built a cuckoo wristwatch". Beyond impractical: "I built a cuckoo wristwatch but there was no room for a working mechanism".
I don't see the relationship between "fun and learning" and "(beyond) impractical".
I enter most of my learning project from the assumption that I could just buy/install whatever I am building and save time/money.
Please consider seeing things from a different perspective than "your book".
Not saying this to antagonise you, but because a lot of time reading comments like this makes other posters less willing to share their impractical efforts, and would love to read more of those, not less.
How is it useless? If it has an NPU it is literally built to run models.
You're just extremely biased in what you consider to be a useful ML model. For example, for some strange reason you think only LLMs exist. The model must be as big as possible or else it is pointless.
Training custom non-LLM models for specific tasks so they run on a resource constrained device? You must be insane.
There's a neat project out there that can read your water meter into home assistant using an ESP32+camera+computer vision. I imagine a small TPU like this could be very useful for similar projects. More compute means higher resolutions and more reliability.
Well, that's sub-$0.50. But yeah, CH32V003 is in that ballpark, and some of the cheapest Microchip and Infineon products are around $0.20.
It's almost never worth it to buy the cheapest chip unless you're making a million of something, but there are very good ones around $1-$2, and $5 is the upscale stuff.
Dave "EEVblog" Jones did a review of a (then) $0.03 microcontroller (Padauk) a while back (sorry, I don't know the exact episode).
Iirc an important caveat was that it was a one-time programmable (OTP) part. So you buy a bunch of them, programming failure or firmware-under-test doesn't work? -> toss the part. Of course that isn't an issue for a $0.03 part. But it can be an issue in terms of a board you want it on. Either that means discarding (breakout) boards too, or for development you'd need some kind of adapter to put bare ICs in.
Such annoyances only make sense for high-volume, low cost applications. Which is eactly where parts like that go in.
I think that is pretty ungenerous. Before ARM, ISAs were not a commodity, and there were only closed, proprietary implementations of them (usually from a single vendor). Arm licensing its IP and actual designs was hugely beneficial for the broader ecosystem and led to their prevalence in the embedded space. The toolchain and software network effect made it a no-brainer to either reach for a completed Arm design, contract a customized one, or build your own.
The arm experiment ran its course though; the power one vendor had in the marketplace started to be abused for the benefit of the IP holder and detriment to others. Now RISC-V is going one step further with a completely open ISA and also completely open designs. This is an excellent development in the nick of time.
I wonder how Apple feels about arm64 and RISC-V now. They could have probably bought ARM at any point but maybe never considered it to avoid anti-monopoly blowback.
This is a really neat use of the per-layer embedding trick. It's also worth noting that there viable TTS models that are ~20-30M param, so it might mean you can have a ESP32 with no network access read stuff out to you in near real time!
One of the things I have been wanting to try for a while now is something like this with a layer per MCU. I have some crazy ideas with RP2350's talking to each other with dedicated lines fed by PIO going through a combination of interpolators and dual multiply instructions.
PSRAM, Flash, and even SD cards may not have the best bandwidth individually, but they can reach quite impressive rates when you have a shitton of them running all at the same time.
The large scale dedicated hardware systems will still have the edge for performance per watt, but the low entry level and slow incline does make these things quite appealing.
PIO to PIO between two rp2350s should be able to transfer as many bits per clock as you can spare pins for.
They have a single cycle double multiply per core, and the interpolators give you a heap of ability
The PIO can be awkward, but you can run a bunch of them at once. Going from MCU to MCU you don't even need to involve the CPU cores, PIO to PIO Comms via pins
You are obviously not going to get big TOPS from it because a Trillion is a ridiculous amount anyway. But never underestimate the power of controlling the whole pipeline.
Ultimately none of the other things I'm doing with MCUs are practical, why would this to be any different.
Running some quick numbers shows you should be able to get >1Gbps. But I seriously doubt you could get those speeds in reality. You would need to get them perfectly in sync, which would likely take a dedicated board and some great knowledge of the oscillator.
As someone who has done a reasonable amount with PIO, I do not think this is possible. However, that should not stop you. If you get it to work, please ping me.
Depending on where you slice the model up, it can be not a whole lot of data. For instance each transformer block outputs a single vector in an embedding space.
I can see that being cheaper to bitbang with PIO than to actually compute.
There's certainly some latency stack up, but throughput should be remarkably good.
My goto for what I hate about modern tech is toothbrushes having Bluetooth and needing apps.
Not that I hate all modern tech but if it needs an app I probably will.
I'm with you there. My fridge has a wifi connection with an app.
The only function it can do is notify me if the door is open. Thats it. Absolute waste of resources. I openend the enclosure and removed the antenna of course.
That's incredible. Sure, not practical for most applications, but if you really want a local top tier model, you can run it on anything as long as you are patient.
As someone with a healthy amount of RAM, but just a 16GB GPU, I am wondering what kind of work I could queue up for overnight runs. I thought the best models were fully out of reach, but the 128GB CPU only test had a 1.8 tokens/second. While not speedy, you could probably do something with that given extensive coffee breaks. This speed simulator[0] demos what it looks like.
So while SSD streaming is interesting I'm not sure it's exactly the same thing as the per-layer embedding that is being utilized in tandem with streaming here. To utilize per-layer embedding, it would have had to be trained that way, which GLM 5.2 was not.
more interesting would be using some kind of FPGA to logic glue each RAM socket interface bitplane to a hard drive (so a collection of hard drives with ridiculous collective bandwidth). Perhaps a single RAM socket contains actual RAM and the linux kernel would have to be modified to only use the real RAM memory region for OS and inference software, with the inference software rewritten to stream LLM weights deterministically from the hijacked RAM slot physical memory regions. Obviously the FPGA can't truly achieve the CAS latencies over the HDD (unless the HDD firmware was rewritten so it can predict the next deterministic token sufficiently in advance to cache the result and stream it just in time to FPGA then "RAM" socket...) but even if the HDD firmware can't be reprogrammed for some reason, the FPGA knows what memory address will be deterministically fetched next, so it can make the requests to the parallel array of HDD's ahead of time.
My guess is because the ESP32's flash is only ~1/4 the bandwidth of the internal SRAM. If you do this on a more powerful system not only is the gap much wider but you also have much more compute you need to keep fed with bandwidth to be efficient.
It's also mapped into the address space so there's very little extra latency in grabbing the embedding as opposed to something like nvme that will have to setup a command list, submit it to the drive's microcontroller, wait for the op to be processed, etc.
If you want to do this at the $1 price point, you can on RP2350, albeit with some limitations. In particular, it maxes out at full speed (12Mbps). The trick is to use the on-chip USB peripheral for one, and connect the other to GPIO pins backed by PIO.
This works today with tinyusb and pico-pio-usb, but I'm also playing with a Rust port which I'm hoping will have higher performance.
$8 ish gets you an ESP32-S3 board with PSRAM, flash, and two USB-C ports. The PSRAM and flash are specifically used for this LLM project. I can't find anything like that with the RP2350 for $1.
It's quite sad people collectively behave as if leaderboards have served their time.
In the small parameter regime there is no room for benchmaxxing, so instead of leaderboards becoming useless, their utility was merely reduced to establishing ever smaller models with similar performance on the benchmarks, forcing compression or redundancy to be recognized and eliminated at the modeling level.
Pretty incredible performance for the footprint - really interested to see what could be done on slightly more powerful SBCs like some that have been mentioned in this thread.
https://milkv.io
The duo has up to 256MB of memory, and a 1TOPS@INT8 TPU. They run Linux and are $5. I bought 5!